Rear Baer Brake Systems for 1964-1966 Mustang with 8″ or 9″ Rearend

$2,445.00$3,795.00

Clear

California Prop 65 Warning 

Description

Rear Baer Brake Systems for 1964-1966 Mustang with 8″ or 9″ Rearend with standard small bearing.  Includes park brake assembly and cables. 

Pro+ Brake System Features

  • 2-piece forged caliper design with six cross bolts for added strength
  • Stainless steel pistons, abutments and noise suppression springs
  • Staggered piston sizes to minimize pad wear
  • Dual seals (dust/weather and pressure) to meet D.O.T specifications
  • Available with 13” and 14” rotors.
  • Machined logo that is hand painted
  • Red, Black or Silver Powder Coat Finish
  • Uses the same pad as the C5 (1997 – 2004) and C6 (2005 – 2012) Corvette for easy, cost effective pad replacement
  • Uses the C5 and C5 backing plate (1997-2012 Corvette) or the FMSI #D731
  • Uses correct banjo style fittings, Baer does not use any pipe thread
  • 6061 T-6 billet aluminum hat (anodized black) and bolted to the rotor
  • High-grade U281 fine thread stainless hardware (with captured nuts). Rotor comes pre-assembled.
  • Includes a set of 6061-T6 billet machined hubs with Timken or SKF bearings installed. Hubs are pre-assembled with bearings, races, studs, and packed with Redline synthetic grease.

 

Extreme + Brake System Features:

  • 1-piece Forged MonoBlock caliper, machined out of a single piece of 2618 forged aluminum.
  • Stainless steel pistons, abutments and noise suppression springs
  • Staggered piston sizes to minimize pad wear
  • Dual seals (dust/weather and pressure) to meet D.O.T specifications
  • Machined logo that is hand painted
  • Red, Black or Silver Powder Coat Finish
  • Uses correct banjo style fittings, Baer does not use any pipe thread
  • Uses the common D1247 (DR11) race pad backing plate that is shared by many other competition calipers
  • 6061 T-6 billet aluminum hat (anodized black) and bolted to the rotor
  • High grade U281 fine thread stainless hardware (with captured nuts). Rotor comes pre-assembled.
  • Includes a set of 6061-T6 billet machined hubs with Timken or SKF bearings installed. Hubs are pre-assembled with bearings, races, studs, and packed with Redline synthetic grease.

100% MADE IN USA with U.S.-sourced material

Wheel Size Fitment

13″ Rotor – 17″ Wheels

14″ Rotor – 18″ Wheels

(Use template to verify fitment)

Instructions

8in_9in_GM_Non_Clip_ALL.pdf

Installation Instructions

Temp_65-67_Mustang_Pro_14.pdf

Pro 14 Template

Temp_65-67_Mustang_Ext_14.pdf

Extreme Pro 14 Template

Additional information
Caliper Color

, ,

Caliper Design

,

Rotor Diameter

,

Suspension location

Suspension type

, , , ,

Year

, ,

Make

Model

Reviews (0)

Reviews

There are no reviews yet.

Be the first to review “Rear Baer Brake Systems for 1964-1966 Mustang with 8″ or 9″ Rearend”

Vehicle Fitment
Make Model Year
BUICK GS 1970 - 1972
BUICK GS 455 1970 - 1972
BUICK SKYLARK 1964 - 1972
BUICK SPECIAL 1964 - 1969
BUICK SPORTWAGON 1964 - 1972
CHEVROLET CAMARO 1967 - 1969
CHEVROLET CHEVELLE 1964 - 1972
CHEVROLET CHEVY II 1968
CHEVROLET EL CAMINO 1964 - 1972
CHEVROLET MALIBU 1964 - 1967
CHEVROLET MONTE CARLO 1970 - 1972
CHEVROLET NOVA 1969 - 1974
FORD FALCON 1961 - 1965
FORD MUSTANG 1964 - 1966
OLDSMOBILE 442 1964 - 1971
OLDSMOBILE CUTLASS 1964 - 1972
OLDSMOBILE CUTLASS SUPREME 1967 - 1972
OLDSMOBILE F85 1964 - 1972
OLDSMOBILE VISTA CRUISER 1964 - 1972
PONTIAC ACADIAN 1968 - 1971
PONTIAC FIREBIRD 1967 - 1969
PONTIAC GRAND PRIX 1969 - 1972
PONTIAC GTO 1964 - 1972
PONTIAC LEMANS 1964 - 1972
PONTIAC TEMPEST 1964 - 1970

Rear Baer Brake Systems for 1964-1966 Mustang with 8″ or 9″ Rearend

$2,445.00$3,795.00

Clear

California Prop 65 Warning 

Description

Rear Baer Brake Systems for 1964-1966 Mustang with 8″ or 9″ Rearend with standard small bearing.  Includes park brake assembly and cables. 

Pro+ Brake System Features

  • 2-piece forged caliper design with six cross bolts for added strength
  • Stainless steel pistons, abutments and noise suppression springs
  • Staggered piston sizes to minimize pad wear
  • Dual seals (dust/weather and pressure) to meet D.O.T specifications
  • Available with 13” and 14” rotors.
  • Machined logo that is hand painted
  • Red, Black or Silver Powder Coat Finish
  • Uses the same pad as the C5 (1997 – 2004) and C6 (2005 – 2012) Corvette for easy, cost effective pad replacement
  • Uses the C5 and C5 backing plate (1997-2012 Corvette) or the FMSI #D731
  • Uses correct banjo style fittings, Baer does not use any pipe thread
  • 6061 T-6 billet aluminum hat (anodized black) and bolted to the rotor
  • High-grade U281 fine thread stainless hardware (with captured nuts). Rotor comes pre-assembled.
  • Includes a set of 6061-T6 billet machined hubs with Timken or SKF bearings installed. Hubs are pre-assembled with bearings, races, studs, and packed with Redline synthetic grease.

 

Extreme + Brake System Features:

  • 1-piece Forged MonoBlock caliper, machined out of a single piece of 2618 forged aluminum.
  • Stainless steel pistons, abutments and noise suppression springs
  • Staggered piston sizes to minimize pad wear
  • Dual seals (dust/weather and pressure) to meet D.O.T specifications
  • Machined logo that is hand painted
  • Red, Black or Silver Powder Coat Finish
  • Uses correct banjo style fittings, Baer does not use any pipe thread
  • Uses the common D1247 (DR11) race pad backing plate that is shared by many other competition calipers
  • 6061 T-6 billet aluminum hat (anodized black) and bolted to the rotor
  • High grade U281 fine thread stainless hardware (with captured nuts). Rotor comes pre-assembled.
  • Includes a set of 6061-T6 billet machined hubs with Timken or SKF bearings installed. Hubs are pre-assembled with bearings, races, studs, and packed with Redline synthetic grease.

100% MADE IN USA with U.S.-sourced material

Wheel Size Fitment

13″ Rotor – 17″ Wheels

14″ Rotor – 18″ Wheels

(Use template to verify fitment)

Instructions

8in_9in_GM_Non_Clip_ALL.pdf

Installation Instructions

Temp_65-67_Mustang_Pro_14.pdf

Pro 14 Template

Temp_65-67_Mustang_Ext_14.pdf

Extreme Pro 14 Template

Additional information
Caliper Color

, ,

Caliper Design

,

Rotor Diameter

,

Suspension location

Suspension type

, , , ,

Year

, ,

Make

Model

Reviews (0)

Reviews

There are no reviews yet.

Be the first to review “Rear Baer Brake Systems for 1964-1966 Mustang with 8″ or 9″ Rearend”

Vehicle Fitment

Rear Baer Brake Systems for 1964-1966 Mustang with 8″ or 9″ Rearend

$2,445.00$3,795.00

Clear

California Prop 65 Warning 

Description

Rear Baer Brake Systems for 1964-1966 Mustang with 8″ or 9″ Rearend with standard small bearing.  Includes park brake assembly and cables. 

Pro+ Brake System Features

  • 2-piece forged caliper design with six cross bolts for added strength
  • Stainless steel pistons, abutments and noise suppression springs
  • Staggered piston sizes to minimize pad wear
  • Dual seals (dust/weather and pressure) to meet D.O.T specifications
  • Available with 13” and 14” rotors.
  • Machined logo that is hand painted
  • Red, Black or Silver Powder Coat Finish
  • Uses the same pad as the C5 (1997 – 2004) and C6 (2005 – 2012) Corvette for easy, cost effective pad replacement
  • Uses the C5 and C5 backing plate (1997-2012 Corvette) or the FMSI #D731
  • Uses correct banjo style fittings, Baer does not use any pipe thread
  • 6061 T-6 billet aluminum hat (anodized black) and bolted to the rotor
  • High-grade U281 fine thread stainless hardware (with captured nuts). Rotor comes pre-assembled.
  • Includes a set of 6061-T6 billet machined hubs with Timken or SKF bearings installed. Hubs are pre-assembled with bearings, races, studs, and packed with Redline synthetic grease.

 

Extreme + Brake System Features:

  • 1-piece Forged MonoBlock caliper, machined out of a single piece of 2618 forged aluminum.
  • Stainless steel pistons, abutments and noise suppression springs
  • Staggered piston sizes to minimize pad wear
  • Dual seals (dust/weather and pressure) to meet D.O.T specifications
  • Machined logo that is hand painted
  • Red, Black or Silver Powder Coat Finish
  • Uses correct banjo style fittings, Baer does not use any pipe thread
  • Uses the common D1247 (DR11) race pad backing plate that is shared by many other competition calipers
  • 6061 T-6 billet aluminum hat (anodized black) and bolted to the rotor
  • High grade U281 fine thread stainless hardware (with captured nuts). Rotor comes pre-assembled.
  • Includes a set of 6061-T6 billet machined hubs with Timken or SKF bearings installed. Hubs are pre-assembled with bearings, races, studs, and packed with Redline synthetic grease.

100% MADE IN USA with U.S.-sourced material

Wheel Size Fitment

13″ Rotor – 17″ Wheels

14″ Rotor – 18″ Wheels

(Use template to verify fitment)

Instructions

8in_9in_GM_Non_Clip_ALL.pdf

Installation Instructions

Temp_65-67_Mustang_Pro_14.pdf

Pro 14 Template

Temp_65-67_Mustang_Ext_14.pdf

Extreme Pro 14 Template

Additional information
Caliper Color

, ,

Caliper Design

,

Rotor Diameter

,

Suspension location

Suspension type

, , , ,

Year

, ,

Make

Model

Reviews (0)

Reviews

There are no reviews yet.

Be the first to review “Rear Baer Brake Systems for 1964-1966 Mustang with 8″ or 9″ Rearend”

Vehicle Fitment